Home > Accessories
Choose a sub category:
Buttons Hardware Lights
Mounting Power Supply Wiring kit
RFID Tags Protective Components
Accessories for our products and general items useful in escape rooms.
Sort By:
Page of 2
1000, 1K Resistors FX51 Shaft Mount Kit Consulting - $125/hr
Box of 1000, 1K metal film resistors for generic Arduino boards (Raspberry PI as well) because the internal pull-up resistor value is not sufficient for off-board, real world applications.  Suitable for 5V and 12V systems.  Consider using 2, one as a pull-up and one as series protection device.  Add a capacitor for additional filtering capabilities!  Proven to help in building more reliable escape room props and controllers.

FX51 Holder and 1/2" or 3/4" Shaft Adapter with Magnet.


(FX board not included, shown for mounting illustration only.)

Hourly consulting, minimum one hour.

Bad Ass Controller Black Plastic Case DIN Rail Kit w/ Full Enclosure - BAC FX350/450 Controller DIN Rail Kit - BAC FX350/450

Black case exclusively for our Bad Ass Controller

Just the box.

Mount your FX controller or other 72mm wide board on DIN rail inside a NEMA rated enclosure. DIN rail mounting is the standard for industrial enclosure electronics. Because the rail is mounted in your enclosure before any other electronics, any plastic and metal shavings can be cleaned out before you mount any electronics. Furthermore, because of it’s versatile, flexible, and universal nature, it allows the builder to rearrange items for optimal wiring, and replace components without turning screws (which can make more shavings in metal cabinets).

Mount your FX450 or other 72mm wide board on DIN rail. DIN rail mounting is the standard for industrial enclosure electronics. Because the rail is mounted in your enclosure before any other electronics, any plastic and metal shavings can be cleaned out before you mount any electronics. Furthermore, because of it’s versatile, flexible, and universal nature, it allows the builder to rearrange items for optimal wiring, and replace components without turning screws (which can make more shavings in metal cabinets).

Plastic Enclosure - BAC FX350/450 Surface Mount Bracket - BAC FX350/450 FX10 Dual 8, 16 Total, Input Match Controller

Securely mount your FX350 with this enclosure. Suitable for applications where AC is involved, dusty areas, and attics.

9"x5.9"x3.4"(230mmx150mmx87mm) ABS body, clear plastic lid.

Comes with mounting points for the FX350.

Easily mount your FX350 or other 72mm wide board on a surface. Sometimes you just need to mount the board on the wall or in a prop and the environment provides sufficient protection or you don’t have the space. The surface mount adapter will protect the controller’s bottom side and provide an easily maintainable way to mount and adjust your controller as needed. If you need to mount your controller with wood screws, use this. It is NOT recommended to place wood screws (or other course, self-tapping screws) through a PCB. It can damage them and void your warranty.

Dual, 8 input compare controller with individual outputs.
I2C Amplifier and Distribution Board - FX14-AMP I2C Distribution Board - FX14-DIST Lever Switch Bracket w/ Switch and Hardware

Extend I2C signals far!  Use one on either end.  I2C in -> I2C out.

I2C Distribution board for better layout of I2C cables.  

Take the hassle out of mounting lever switches. Necessity is the mother of invention. We were tired of coming up with creative and suboptimal ways to mount lever switches, so we built this. It’s a simple bracket that can support the mounting in over a dozen ways. And if you need even more ways, drop it in a vice, make a new bend and get the bracket just the way you need it.

Includes screws and nuts for mounting AND includes the switch!

1 Light and 1 Button Install Kit 2 Lights and 2 Buttons Install Kit Magnets 1/4" N42 Cylinders, Rotary Detection

Get control to your escape room! The combination of a push button and a status light mounted on a stainless-steel wall plate creates a professional presentation and installation for remotely controlling your room. This rugged and simple design provides a user interface for your game master to control the room.

Designed for use with FX350 Room Controller, the button and light typically are used to start a room and let the game master know when the room timer is running. However, when connected to the FX350 and appropriate room control software, the button and light can be configured to do most anything.

Get control to your escape room! The combination of two push buttons and two status lights mounted on a stainless-steel wall plate creates a professional presentation and installation for remotely controlling your room. This rugged and simple design provides a user interface for your game master to control the room.

Designed for use with FX350 Room Controller, one button and light typically are used to start a room and let the game master know when the room timer is running. The second button and light typically start the video and advise if the room is in use. However, when connected to the FX350 and appropriate room control software, the button and light can be configured to do most anything.

Want less? Check out the one light/one button version here.

High strength rare earth magnets for use with the FX51-D and FX51-SEN when using rotation detection.

N42 Material, cylindrical, 1/4” major diameter, 1/8" hole diameter, 1/4” tall.

Shinny.

Magnets 1/2" N42 Cylinders, Rotary Detection Magnets 1/2" N52 Cylinders 12V, 2A Power Supply

High strength rare earth magnets for use with the FX51-D and FX51-SEN when using rotation detection.

N42 Material, cylindrical, 1/2” major diameter, 3/16" hole diameter, 1/4” tall.

Shinny.

High strength rare earth magnets for use with the FX50, FX51-A, FX51-D or any other use for magnets in your escape room.

N52 Material, cylindrical, 1/2” diameter, 1/2” tall.

Shinny.

Power Supply! (May vary from picture)
24V, 1A Power Supply RFID Tag, EM4200 16mm Black Plastic Disk RFID Tag, EM4200 25mm Clear Plastic Disk w/ Sticker Backing)
Power Supply! (Picture may vary from item.)

EM4200 16mm Black Plastic Disk Tag

Works with our RFID Reader System

EM4200 25mm Clear Plastic Disk Tag

Works with our RFID Reader System

RFID Tag, EM4200 40mm Clear Plastic Disk w/ Sticker Backing) I2C 4 Pin Jumper Cables 6" Length I2C 4 Pin Jumper Cables 12" Length

EM4200 40mm Clear Plastic Disk Tag

Works with our RFID Reader System

I2C Jumper Cables,  6" Length I2C Jumper Cables, 12" Length, 4 conductor.
I2C 6 Pin Ribbon cables 12" Length I2C 6 Pin Ribbon cables 48" Length 12V, 1A Power Supply
I2C Ribbon cables 12" Length I2C Ribbon cables 48" Length Power Supply!
24V, 2A Power Supply Touching Hands Interface  - FX16-TH Protective MOV for 110V AC systems
Power Supply!

Exact model may vary.
Coming soon!  Call us! Protective MOV (Metal Oxide Varistor) for 110V AC systems.

MOV/Varistors 205V 400A 100pF